TELEMAC-MASCARET Forum: Select areas for the serafin output result file (1/1)

Welcome, Guest

TOPIC: Select areas for the serafin output result file

Select areas for the serafin output result file 11 years 3 days ago #13630

mary
OFFLINE
Junior Boarder
Posts: 33
Thank you received: 1

Dear all,

I'm working with a really heavy model in which the post-processing stage takes too much time.

I would like to know if it is possible to define an output serafin results file where I would have just some areas/regions of the model domain. If so, could you guide me on how to get that? If not, would it be possible to write directly the results file in the netCDF format?

Thanks in advance.

Kind regards,
Maria

The administrator has disabled public write access.

Select areas for the serafin output result file 11 years 3 days ago #13641

jmhervouet	Hello, It is not possible so far to write directly a netCDF file. Another possibility if you work in parallel is to look at only one subdomain... Regards, Jean-Michel
	The administrator has disabled public write access.

Select areas for the serafin output result file 11 years 3 days ago #13642

mary OFFLINE Junior Boarder Posts: 33 Thank you received: 1	Dear Jean-Michel, Thanks for your reply. And is it possible to define just a number of sections in the model domain as output file with serafin format?If so, could you guide me on that? Cheers, Maria
	The administrator has disabled public write access.

Select areas for the serafin output result file 11 years 3 days ago #13645

jmhervouet	Dear Maria, No, cross sections are done by Postel3D as a post-treatment, so you need first to get the large results file... Regards, JM
	The administrator has disabled public write access.

Select areas for the serafin output result file 11 years 21 hours ago #13649

mary
OFFLINE
Junior Boarder
Posts: 33
Thank you received: 1

Dear Jean-Michel,

Thank you again for your reply. I never worked directly with postel3d. I have tried to run the test case "wave" and it runs well. Nevertheless when I run the test case "vent" I have an error. I attach the ouput log file. Do you have any idea where the error comes from? The differences that I see between the two test cases is that the "wave" test case has already the results file in the directory, while in the "vent" test case we have to run first telemac3d and then postel3d.

Kind regards,
Maria

The administrator has disabled public write access.

Select areas for the serafin output result file 11 years 21 hours ago #13651

mary
OFFLINE
Junior Boarder
Posts: 33
Thank you received: 1

I'm sorry but I cannot attach the file. I copy paste here the error that I get:

MAILLAGE : MESH3D ALLOUE

MAILLAGE 2D

2D element type : 10
nombre de points 2D : 315
nombre d'elements 2D : 543
nombre de points de bord 2D : 85

MAILLAGE 3D

3D element type : 40
nombre de points 3D : 4725
nombre d'elements 3D : 7602
nombre de plans : 15
nombre d'elements de bord : 1190
nombre total de points de bord : 1905
dont cotes lateraux : 1275
surface : 315
fond : 315
****************************************
* FIN DE L'ALLOCATION DE LA MEMOIRE : *
****************************************

LIT : ERREUR DE LECTURE
ON VOULAIT LIRE UN
ENREGISTREMENT DE 4725 VALEURS
DE TYPE : R4
SUR LE CANAL : 4

PLANTE : ARRET DU PROGRAMME APRES ERREUR
_____________
runcode::main:
/projects/13_131_bevaarbozs/vent:
|runCode: Fail to run
|/projects/13_131_bevaarbozs/vent/p3d_vent.cas_2014-07-14-11h28min58s/out_postel3d

Maria

The administrator has disabled public write access.

Select areas for the serafin output result file 11 years 11 hours ago #13654

jmhervouet	Hello, A known error for previous versions of Postel-3D is that it did not understand the date in the Selafin format. Could it be this ? It has been corrected, maybe in V6P3R2 (not sure) or in the trunk (sure). Version 6.3 of T-3D always gives a date I think. JMH
	The administrator has disabled public write access.